Vitrek 954 HiPot Insulation Resistance Tester 11KVdc 6KVac 40Amp GB
The Vitrek 954 HiPot Insulation Resistance Tester 11KVdc 6KVac 40Amp GB Test
The Vitrek 954 HiPot Insulation Resistance Tester 11KVdc 6KVac 40Amp GB features:
- 11KVDC/6KVAC Electrical Safety Compliance test voltages
- Insulation Resistances to 4TΩ
- Low Continuity Ohmmeter: 100µΩ to 149KΩ
- High Power: 200VA standard Option to 500VA
- Max Leakage Current: 50mA (100ma w/500VA opt)
- 50mA Current Sourcing
- Ground Bond Testing to 40Amps
- Ramp Times Programmable 0.01 to 9999sec
- Dwell Times: 0.02 to 9999sec
- HSSD™ High Speed Solid-State load Discharge – removes HV Test load voltages faster than passive resistor designs
- SFI™ Safety Fault Interrupt – shuts down output in as little as 50uS from detection,
- TLSS™ Test Lead Safety Sense – continuously verifies that test leads have proper connections prior to and during HV and continuity testing,
- Start switch design prevents inadvertent actuation
- Dual Channel current measurement detects earth leakage faults
The Vitrek 954 HiPot Insulation Resistance Tester 11KVdc 6KVac 40Amp GB Test uses Modern DSP Technology Design
The Vitrek 954 HiPot Insulation Resistance Tester 11KVdc 6KVac 40Amp GB test utilizes Modern DSP Technology. Consequently, this design feature brings you the fastest, most capable, feature-rich Hipot Ground Bond tester available for a surprisingly low price. Additionally, it provides for extremely low leakage current measurements. Furthermore, Vitrek 954i HiPot Insulation Resistance Tester 11KVDC 6KVAC features a 4-wire milli-ohmmeter with dynamic range up to 100KΩ.In addition to that, there is an overlapping Tera-ohm class Insulation Resistance function. Also this design brings a 40 Amp Ground Bond test capability to the party. Now you’re just beginning to get a feel for what the new Vitrek 954i HiPot Tester can do for you. Additionally, choose from Vitrek’s family of Electrical Safety Compliance Testers, 951i, 952i, 954i, 954i, 955i, 957i or 959i. One of these Safety Testers will fit your application as well as your budget.
A few of the Vitrek 954 HiPot Insulation Resistance Tester 11KVdc 6KVac 40Amp GB Features and Benefits:
- Highest Level of Operator Safety – features include: HSSD™ High Speed Solid-State load Discharge. Incidentally, this design feature Removes Test Voltages far faster than passive resistor designs. Also the SFI™ Safety Fault Interrupt shuts down output in as little as 50µsec from detection. TLSS™ Test-Lead-Safety-Sense continuously verifies that test leads have proper connections prior to and during HV and continuity testing. Start switch implementation prevents inadvertent HV actuation. Dual Channel Current Measurement also detects earth leakage faults.
- High Power Output – means not only better drive capability but also faster test throughout. With up to 50mA of current sourcing for AC & DC Hipot the 950i Series gets heavy duty jobs done faster. Also optionally available, the 200mA drive tackles even tougher sourcing requirements.
- Wide Range of built-in Voltage Capabilities – starting at 6KV AC/DC extending to 10KVAC and 11KVDC or up to 30KV RMS AC with external option
A Few More Features:
- The Fastest Hipot Testers available! Thanks not only to our Dual Coldfire® microprocessors but also in combination with Dual-DSPs to provide Ramp-rates up to 50KV/second. Dwell times as low as 20mS and overall test times as fast as 3mS in optional Flash mode.
- Expansive Test Sequence Memory – holds up to 100 tests with up to 100 steps per test. Tests selections are via front panel. RS232 or Digital I/O or with optional GPIB/Ethernet are also available.
- Ground Bond Test Capability is available in three models with output currents from 100mA to 40Amps RMS. In addition, test times are programmable from 20mS to 1000 seconds or longer.
- 4-Wire Milli-Ohmmeter Function provides fast, accurate 5 digit resistance measurements with resolution down to 100µΩ and range up to 100KΩ.
- Built-in Phase-Angle Measurement allows the measurement/display of both resistive-in-phase leakage current and reactive-out-of-phase leakage current due to capacitive coupling.
Additionally, Even More 954i HiPot Insulation Resistance Tester 11KVDC 6KVAC 40Amp GB Benefits:
- Multi-Dwell Functionality – permits dwells at different voltage levels without having to return to zero between test steps. Additionally, this dramatically simplifies analysis of dielectric properties.
- Ramp High/Dwell Low Current Limits – permits the user to set separate limits for the ramp and dwell times. Ramp and dwell settings not only provide faster ramp times but also lower leakage test limits.
- LAN/Ethernet-USB Print-RS232-Digital I/O-Scanner/Control – All Standard Interfaces – Provides the highest level of test automation. Full serial control and DI/O with remote start/stop also provides safety fault interrupt, test select & more
- High Voltage Scanner Control – up to 256 point HV-switching capability can be handled via the standard VICL auxiliary-control port. Available scanners can route voltages up to 15KV and currents up to 40A for multi-point Hipot and Ground-Bond test requirements
Also, Additionally Just in Case, a Few More Features:
- Dual Dimensional / Test Specific / Broadband Arc Detection – Lesser testers allow a single, global, amplitude setting only arc limit. In contrast, the technologically superior 950i Series utilizes time & amplitude dependent arc limits. The 950i uniquely applies them to each desired test
- Hard Copy Test Report, Ethernet and GPIB – all available via optional interface card. Host USB printer control port generates comprehensive test report at the touch of a button. Also, LAN and GPIB ports offer robust industrial interface formats
- Pico-Amp Leakage Measurement – insures that even the lowest leakage current levels measurements are accurate. In addition the tera-ohm(TΩ) range IR readings are also stable and precise
- Test Specific Fixture & Cable Compensation – Automatically calibrate out offset errors due to lead resistance, fixture capacitance and leakage. Compensation constants are kept for each test and with editing available at the touch of a button
The Features Just Don’t Stop:
- Multi-Mode IR – Choose either AC IR or DC IR to suit your measurement requirement. Insulation Resistance values up to one Tera-ohm are available with precise results. You choices of 3 IR test modes – end test on timer, end test on pass reading or fail reading.
- Continuously Variable IR Test Voltage – Most IR testers limits testing to 3 or 4 discrete test voltages. In contrast, the 950i Series allows you to select the test voltage you need. This feature means starting as low as 2V all the way to 6.5KV or 11KV in the higher voltage models
- Capacitance Test Modes – For AC & DC Hipot and IR provides tight control of charge and discharge profiles. Provides superior results on critical solar panel tests and other highly capacitive loads
- Light Weight Switching Power Supply Design – Reduces component count as well as internal heat rise while improving overall reliability. Starting at only 18 lbs, 950i Series portability is a snap
A Timely Finish of Feature Presentations:
- 400Hz AC Voltage Withstand Testing – provides aviation frequency specific test results. As a result one gets far a more effective analysis of dielectric properties on avionic components
- Solar Panel Testing – Design simplifies PV testing. The 950i Series uses pico-amp resolution to detect minute defects in solar cells. Likewise its HSSD High Speed Solid Discharge provides the industry’s safest and fastest throughput rates
- 3 Year Extended Warranty – As a result, Built-in Reliability you can count on for years to come
- Safety Tested – per EN 61010-1. EMC compliant to EN 61326-1
Vitrek 950I Series Abbreviated:
Refer to the Vitrek 957i for 15KVDC Insulation Resistance Hipot Testing
|Vitrek Model||Description||MSRP||Sale Price||e-Quote Special Price|
|Vitrek 951i||951i 6KV AC/DC HiPot, Insulation Resistance and Low Resistance Tester||$4,550.00||$4,458.00||e-QUOTE 951i|
|Vitrek 952i||952i 6KV AC/DC/IR HiPot, Ground Bonding and Low Resistance Tester||$5,195.00||$5,090.00||e-QUOTE 952i|
|Vitrek 953i||953i 11KVDC 6KVAC HiPot, Insulation Resistance and Low Ohm Tester||$5,395.00||$5,286.00||e-QUOTE 953i|
|Vitrek 954i||954i 11KVDC 6KVAC HiPot, Insulation Resistance and Ground Bonding||$6,195.00||$6,070.00||e-QUOTE 954i|
|Vitrek 955i||955i 10KVDC 10KVAC HiPot, Insulation Resistance and Low Ohm Tester||$6,195.00||$6,070.00||e-QUOTE 955i|
|Vitrek_957i||957i 15KVDC 6KVAC HiPot, Insulation Resistance and Low Ohm Tester||$6195.00||$6,070.00||e-QUOTE 955i|
|Vitrek_959i||959i Ground Bond/LR Safety Compliance Analyzer||$3,195.00||$3,130.00||e-QUOTE 959i|
|Vitrek Model||Description||Sale Price||e-Quote P&D|
|PMT-1||PMT-1 Pulse Mode / High Speed Flash Test Option||$495.00||e-QUOTE Vitrek PMT-1|
|AC-2||AC-2 200mA 2 KVAC Output Option||$195.00||e-QUOTE Vitrek AC-2|
|QTPRO-9||QTPRO-9 Test Automation Software for XP, Vista, 7||$395.00||e-QUOTEVitrek QTPRO-9|
|GPIB-9||GPIB-9 Adds a GPIB Interface to your 950i Series||$395.00||e-QUOTEVitrek GPIB-9|
|K1||K1 4-wire Kelvin Low Resistance Measurement Lead Set||$150.00||e-QUOTEVitrek K1|
|950i-K-2||950i-K-2 4-Wire 40 A Ground Bond Lead Set||$185.00||e-QUOTEVitrek 950i-K-2|
|TL-IEC95 IEC||TL-IEC95 IEC Power Socket HV Test lead Set||$95.00||e-QUOTEVitrek TL-IEC95 IEC/a>|
|TL-IEC95GB IEC||TL-IEC95GB IEC Power Socket HV & GB Test lead Set||$195.00||e-QUOTEVitrek PMT-1|
|RM-1||RM-1 Rack Mount Kit||$75.00||e-QUOTEVitrek PMT-1|
|AC-30||AC-30 30 KVAC 10mA External Output Option||$3,295.00||e-QUOTEVitrek AC-30|
|RPO-95||RPO-95 Rear Panel Output||$395.00||e-QUOTEVitrek RPO-95|
|500-VA||500-VA 500VA 5KV 100mA AC Drive||$395.00||e-QUOTEVitrek 500-VA|
|TP-950||TP-950 HV Test Pistol for 95X Series||$295.00||e-QUOTEVitrek TP-950|
|TL-209||TL-209 Standard HV Alligator Clip Test Lead||$85.00||e-QUOTEVitrek TL-209|
|HSS-1||HSS-1 High Side Sense, for measuring grounded DUT's||$495.00||e-QUOTEVitrek HSS-1/a>|