Instek GOM-802 1999 Count Milli-Ohmmeter
The Instek GOM-802 Milli-Ohmmeter is designed for component and material resistance measurements in laboratories and other test environments. A large display with 30,000 counts and a superb accuracy of up to 0.05% gives the reliability and flexibility required in demanding measurement applications. Features such as Auto ranging, a built-in comparator offering Hi-Lo testing, a Limit Percent setting, and Go/NoGo testing reduce the effort for complex testing setups. Displays selections of Relative, Actual, and % Value show results viewed from multiple perspectives. Instek's GOM-802 supports 4 Wire Kelvin resistance measurements for faster accurate results. For an accurate, sophisticated, affordable milliohm meter, the Instek GOM-802 Milli-Ohmmeter is the right choice.. DATASHEET
Instek GOM-802 Milli-Ohmmeter Features |
Instek GOM-802 Milli-Ohmmeter Specifications |
 30,000 Counts Display
|
30,000 Counts Display |
From 30mΩ/1A to 3MΩ/1uA Ranges(9) Resolution 1uΩ on 30mΩ |
30mΩ/1A, 300mΩ/100mA, 3Ω/100mA, 30Ω/10mA, 300Ω/1mA, 3kΩ/100uA, 30kΩ/100uA, 300kΩ/10uA and 3MΩ/1uA 9 ranges |
0.05% Best Accuracy |
30mΩ: ±1% reading + 6 digits |
300mΩ: ±0.05% reading + 6 digits
3Ω: ±0.05% reading + 3digits |
30Ω~3MΩ: ±0.05% reading + 2 digits |
Hi-Lo Limit Comparitor (Go-No/Go Settable) & Percent Setting |
Temperature Measurement: 50°C ~ 100°C |
Measurement of REL, Actual and % Value |
Measurement Rate: 7/sec @ 30,000 Count & 30/sec @ 3000Count |
Four-Terminal Measurement Technique |
Memory: 20 Sets of Data |
| Continuous or Triggered Measurement Mode |
Interface: Standard: Handler, Scan
Option: RS-232C+GPIB |
| Temperature Compensation and Measurement |
Functions: Hi/Lo, Go/No-Go, Trigger, Actual, %, Diode, REL, Temp, TC for Transformer |
Manual or Autoranging
|
Size:251(W)×91(H)×291(D) mm ~ Weight:
Approx. 3kg |
Scan, Handler Interface(Standard)
|
AC Power: 100V/120V/220V/230V±10% , 50/60Hz |
|
Option KCS Gold Plated 4-Wire Kelvin Clip Set
Nylon Bobbin Insulates the set of Clips from each other
|
Option "K" Medium Weight Gold-Plated Kelvin Clip Set:
Useful for custom 4-wire measurements on components, transformer wires, fixtures and a variety of loads. The gold plated "KCS" clips open to 1/2" and accommodate up to 10 amps of test current.
|
Option KCS Gold Plated 4-Wire Kelvin Clip Set-Kit
Nylon Bobbin Insulates the set of Clips from each other |
Opt. "KK" 4 Wire Kelvin Lead Set:
6 feet shielded cable set dual banana type terminated in "JAWS". (Opens 2" )
|
"MP-4"/"MP-5" Kelvin Surface Probe Set
Engineered to support a variety of surface, plating, and bonding resistance measurement requirements. These probes provide repeatable resistance or bond testing on metallic screens, conductive layers, flat or plated surfaces etc. Test current is evenly distributed through the probe base while potential sensing is accomplished via a spring loaded center contact. For consistent results with smaller target areas the "MP-5" offers a reduced surface diameter of 0.5", while "MP-4" is a 1" diameter. |
Opt. MP-5 Kelvin Surface Probe Set
Engineered to support a variety of surfaces, plating, and bonding resistance measurement requirements. These probes repeatable resistance or bond testing on metallic screens, conductive layers, flat or plated surfaces etc. Test current is evenly distributed through the probe base while potential sensing is accomplished via a spring-loaded center contact. Surface diameter is 0.5" while "MP-4" is a 1" diameter..
|
MP-3" Micro-probe
48" shielded cables (dual banana), handheld pencil type, terminated in spring-loaded steel tips with .08" separation (1 Amp max). |
"MP-2" Kelvin Mini-Probe Set
48" shielded cables, handheld pencil type, terminated in spring loaded steel tips with 0.18" separation. (1 Amp max |
|
GOM-802 
